The Compressor Technologies company produces and sells spare parts for the VP-50/8 compressor
All manufactured and supplied products are provided with a certificate of conformity and a quality certificate.
The VP-50/8 reciprocating compressor is used in industry for compressing air with a pressure of 8 kgf / cm2, with a capacity of 50 m3/min.
VP-50/8 compressor – piston, air compression – two-stage.
The VP50/8 compressor cylinders are two – stage.
The compressor is lubricated by a circulating pump, with oil being supplied from the lower part of the frame by a gear pump. The VP 50/8 compressor is equipped with an electric motor of the DSK-173/16-16A type, which rotates the crankshaft and thereby transmits the forward motion to the compressor pistons.
The cylinders and oil seals are lubricated using a multi-plunger pump that supplies oil from the lubricator 32-05-2.
The cooling system of the VP-50/8 compressor unit is water – based. After compressing the gas in the first stage, it enters the refrigerator-gas cooler HRK 8/9, after the second-in the receiver, where it is cooled and fed to the consumer. The automatic control system allows you to control the main parameters of the VP-50/8 compressor, control and emergency stop with a sound and light signal in case of exceeding the permissible operating parameters.
Spare parts of VP-50/8 compressor
Drawing number | Part Name |
---|---|
02A-01 |
Crankshaft |
02-03 |
Counterweight |
02-04 |
Counterweight bolt |
02-05 |
Key ring |
2-1-10D |
Spacer ring |
Stage 1 valve |
PIK 165-0. 4 AM valve |
03-04 |
O-ring |
sb. 8D-M |
Oil seal (special drawing) |
08-07 |
Bracelet spring |
08-13 |
Padding |
sb. 8D-1 |
Support bushing |
sb. 9D |
Presalnik |
2-stage valve |
PIK 165-2. 5 AM valve |
9B-2-5 |
Driven gear |
9B-2-1-1 |
Bushing |
10-00 |
Connecting rod |
10-02 |
Insert |
10-03 |
Bushing |
11-00 |
Crosshead |
11-02 |
The shoe |
11-03 |
Finger |
Lubrication station |
Lubricator 32-04-5 |
11-09 |
Padding |
12a-01 |
Cylinder I stage. |
12b-02 |
Shell case |
12-03 |
Cylinder cover I art. lower |
12-04 |
Cylinder cover I art. top |
13d-07 |
Spring (valve) |
15a-01 |
Cylinder of the second stage. |
15b-02 |
Shell case |
15-03 |
Cylinder cover II art. rear |
15-04 |
Cylinder cover II art. front |
18-00 |
Piston I st. assembly |
18-01 |
Piston I art. |
18-02 |
Stock I art. |
18-05 |
Stem nut |
19-00 |
Piston II art. assembly |
19-01 |
Piston II art. |
19-02 |
Stock II art. |
VP50 03-05 |
Padding |
VP50 03-01-00 |
Reflector assembly |
VP50 03-01-01 |
The reflector |
VP50 03-01-02 |
Ring |
VP 50 07/I 00 |
Drive shaft with flange |
VP50 07-22L |
Drive bushing |
VP50 07-52L |
Bushing |
2-1 |
Padding |
2-8 |
Flashlight |
sb. 2-1 |
Lantern I art. |
3-2 |
Padding |
sb. 3-4A |
The valve is optional. dead space |
3-4-9 |
Locking ring |
3-4-10 |
Locking ring |
sb. 4A |
Crosshead |
4A-1 |
Nut |
4A-2 |
Crosshead finger |
4-3 |
Cap |
4A-4 |
Bolt |
4A-5 |
Cap |
sb. 4-1 |
Crosshead with shoes |
sb.6 |
Piston I art. |
6-1 |
Stock |
sb. 6-1 |
The piston |
sb.7 |
Piston II art. |
sb. 7-1 |
The piston |
Clients of the company "Compressor technology" can get personal consultation about products, and full information about the installation, commissioning and maintenance. The company's policy "Compressor Technology" is aimed solely at long-term relationships with our clients. In our opinion this is the key to success.